A technician in plain workwear standing beside a residential garage door that is partly open, checking the base of the track and the photo eye mounted near the floor in a bright, tidy garage

Garage door repair · Cicero, IN

Garage Door Repair in Cicero

Scraping on the way up, rubbing at the frame, one side higher than the other. We come to your garage, look over the whole door, then fix the part that is holding it back and explain it before we start.

  • Licensed and insured
  • Upfront quote
  • Parts-and-labor warranty

Request a Call Back

Scraping and sticking doors

Garage door repair in Cicero for doors that scrape, stick or hang crooked

A door that scrapes or sticks is a door that no longer runs square. Garage door repair in Cicero for this problem starts with a simple idea: a garage door is a set of parts that have to line up with each other, and when one drifts, the rest start to rub. A track that has moved a little, a roller that has worn flat, a hinge that has loosened or a panel that has bent can all produce the same grinding sound, so we check the whole door before we pick a fix.

Cicero is a town in Jackson Township, Hamilton County, north of Indianapolis. Central Indiana swings from freezing winters to humid summers, and that swing is hard on a garage door: wood trim swells and shrinks, the floor and framing settle a little, and hardware that fit closely in July can bind in January. A door that starts sticking in one season and eases in another is a pattern worth mentioning when you call.

What the door is doing tells us where to look. A scrape that follows the door the whole way up usually points to a track that has shifted or a worn roller. A catch at one spot suggests a bent panel or a loose hinge. A door that tilts as it rises has a side that is lifting faster than the other, and that can mean a cable, a spring or both. If the opener is also straining, opener repair is part of the picture too.

Close-up of a hinge and roller at the edge of a steel garage door panel, hardware fitted straight and secure
Hinge and roller moved across to the new panel

Finding the rub

What we look at on a door that rubs or sticks

Where the door is rubbing

We run the door slowly and watch for the exact spot of contact: the jamb, the track, the weatherstrip or the header. The location narrows the cause before a single bolt is touched.

Track position

The vertical tracks must stand plumb and sit a consistent distance from the door on both sides. Brackets that have loosened let a track lean, and a leaning track pinches the rollers at one point.

Rollers

Rollers carry the door along the track. When a nylon roller cracks or a steel one wears flat, the door jerks and scrapes. We replace the ones that show wear and leave the ones that don't.

Hinges and panels

Hinges join the panels and carry the rollers. A hinge cracked at the knuckle lets a panel sag and catch the track. We also look at panels for a bend or a split along a seam, which can stop the door from folding at the curve.

Level and balance

A door that is higher on one side may have a cable that has stretched or slipped, or springs of unequal strength. We check the bottom edge with a level and balance the door by hand.

Lubrication of moving parts

Dry rollers, hinges and spring coils squeal and drag. After the repair we apply a lubricant made for garage doors to the moving parts, since the wrong kind collects dust and gums up.

Your repair visit

What happens when you call about a scraping door

  1. 01

    Tell us what you hear and see

    Say where the scraping is, whether the door tilts, and whether it gets worse in certain weather. That gives us a starting idea of the cause.

  2. 02

    We come out and examine the whole door

    A uniformed technician runs the door by hand and under power, checks the track, rollers, hinges, cables and springs, and notes every part that is out of line.

  3. 03

    We tell you what we found and quote it

    We point out what is wrong, explain why it causes the scraping, and give you an upfront quote before any work begins.

  4. 04

    We correct it and test the run

    Realigning a track or replacing a roller or hinge is usually done in one visit. We run the door several times to confirm the noise is gone and the door sits square.

Grinding door

A door that grinds is wearing out the parts it grinds against.

Tell us where it scrapes and we'll tell you what it likely needs.

Recent repairs

Doors running square and quiet again

Close-up of a nylon garage door roller and steel hinge with a light film of fresh lubricant, bright daylight
Rollers and hinges freshly lubricated
Close-up of a steel hinge and roller joining two panels of a new garage door inside the track, clean new hardware
A freshly serviced white residential garage door, closed and square in its opening on a tidy brick home exterior in daylight

Cicero door questions

Questions about a scraping or sticking door

Why does my garage door stick more in winter?
Cold stiffens grease and rubber, and a door that fits tightly in warm weather can bind when the frame or the floor shifts a little. Hardware that is dry or worn shows up first. A cleanup and fresh lubrication often eases it, but if the door scrapes at a fixed spot, a track or roller needs attention.
How often should an automatic garage door be serviced?
A yearly check of the track, rollers, hinges, cables and springs catches wear before it turns into a scrape or a stall. A door that has started to make noise should not wait for the year to end.
Is it okay to keep using a door that scrapes?
For a short while, with care. Scraping means something is out of line, and running the door puts more wear on the track and rollers each time. If the door tilts or jerks, stop using it and call us.
Is it worth repairing a damaged door, or should I replace it?
If the problem is a track, a roller, a hinge or a single bent panel, repair is the sensible choice. When several panels are bent or the door will not hold its shape, a replacement door makes more sense than repeated fixes, and we say so when we see it.
How is the price of this kind of repair worked out?
It depends on which parts need replacing, how many, and the size and weight of the door. The technician looks first and gives you an upfront quote before any work starts.
Are repairs covered by a warranty?
Yes. Repairs and installations carry a parts-and-labor warranty, and the technicians are licensed and insured.

Cicero, IN

Door scraping, sticking or hanging crooked?

Tell us what you hear and where. We'll come out, go over the whole door, and explain the fix before any work starts.